Blown-In Insulation in Mississauga, ON
We blow loose fill over the insulation you already have, after we have sorted out what stays and what needs fixing.
We top up attics with blown-in insulation in Mississauga: loose fibreglass or cellulose blown over the insulation that is already there, once anything wrong with the attic is fixed. It suits a house with a dry but thin attic floor, where nothing above the ceiling needs fixing first. We go up, look, tell you plainly what stays, and quote the top-up from there.
Top up, or deal with something first?
If your insulation is dry and just thin, it stays, and the new blown-in goes on top. That is the keep side of the call. A top-up builds on the attic insulation you already have. There is no reason to pull out material that still works.
Wet, soiled or rodent-damaged insulation is another matter. It comes out before anything new goes in, because clean material blown over it only hides the problem. Removal has its own page, attic insulation removal, and we can put the removal and the top-up on one quote.
Frost on the nail tips under the roof deck has to be dealt with before a top-up. So does a bathroom fan duct that stops in the attic instead of running outside. Either one means moist house air is getting into the attic, and more insulation won't stop that. We show you what we found, the right trade fixes the cause, and then we come back to add depth. Our page on frost and mould in the attic covers the signs to watch for.
Baffles at the eaves
Baffles are rigid foam or cardboard channels stapled between the rafters at the eaves to hold insulation back from the soffit vents. They leave a clear path, so outside air can still come in at the soffit and travel up under the roof deck. Our crew fits them before the top-up. Without them, fresh blown-in can drift right into the vents.
Buried soffit vents are one of the usual reasons an attic goes damp. Block the intake and the warm air leaking up from the house just sits there. Its moisture ends up on the coldest surface around, which is the underside of the roof deck.
Adding roof vents or changing how the attic breathes is roofing work, and we don't do it. If we think your attic needs more ventilation, we write that on the quote and leave the decision to a roofer.
Seal the ceiling, then add depth
Air sealing happens before any blowing. Insulation slows heat down, but air goes straight through it, so a warm-air leak at the ceiling keeps carrying heat and moisture into the attic however deep the loose fill is.
These are the gaps we seal, the ones you can't see from the rooms below:
- Top plates, where each interior wall meets the attic floor and the drywall leaves a crack
- Plumbing stacks and vent pipes coming up through the ceiling
- Electrical wires and the holes drilled to run them
- The frame of the attic hatch, where it sits in the ceiling opening
Why the sealing cannot wait
Once fresh insulation covers the attic floor, nobody goes back to seal it. We use caulk or spray foam depending on how big the gap is. In an older Mississauga bungalow or backsplit with its original insulation, these are the first spots we check.
Fibreglass or cellulose
Both are loose fill blown through a hose from a machine outside, and either works in an attic if it goes in deep enough. What separates them in your house is practical stuff:
- Weight: cellulose insulation is heavier at the same depth. On an old plaster ceiling or thin drywall, we check that before picking it.
- Moisture: cellulose can soak up a little moisture and dry out again. Fibreglass doesn't absorb it. Neither one survives a real roof leak, and soaked material of either kind comes out.
- Settling: cellulose settles more once it's blown, so it goes in deeper on the day to end up at the settled depth the bag calls for. Loose fibreglass settles less.
- Dust: cellulose throws more fine dust during the job. Fibreglass is less dusty but sheds itchy fibres, so we cover the hatch area and the floor under it either way.
- Low attics: cellulose gets to a given R-value in less depth. That helps near the eaves and in a shallow attic where you don't have height to spare.
Which one goes in your attic
It depends on the house. The quote says which one we'd use and why, so you can think it over before anything gets blown.
How deep, and how to check it
SB-12, the energy efficiency standard that goes with the Ontario Building Code, sets a minimum nominal R-60 for a ceiling with attic space in Zone 1 under packages A1, A2, A4 and A6, and R-50 under A3 and A5. Those rules are written for new houses. When you're adding insulation to the attic floor of an existing home, treat them as a sensible reference point, not a requirement.
There isn't one depth for a given R-value. The coverage chart printed on the product's bag lists the settled depth for each R-value, and it varies from product to product. Ask your installer to show you the chart for the bag going into your attic.
Depth markers let you check the result after we've gone. They're cardboard rulers stapled to the joists across the attic before blowing, printed big enough to read from a distance. To check them from the hatch:
- Get on a sturdy ladder, push the hatch up and slide it aside. Don't climb in.
- Shine a flashlight across the attic floor until you spot the depth markers.
- Read where the top of the insulation meets each marker and compare it with the settled depth on the coverage chart.
- Pay the most attention near the hatch and out toward the eaves, where blown-in tends to end up thinner.
- Keep off the insulation. The ceiling drywall between the joists won't hold you.
When a top-up is the wrong job
Sometimes the straight answer is not to blow anything yet:
- Frost or mould in the attic. We wait until the cause is found and fixed, because new insulation would just sit in the same moist air.
- Vermiculite. This is where we put the tools down. Work stops, nobody touches it, and we recommend you have a qualified lab or an abatement firm test it before anything else happens. We don't sample, test or remove it, and we don't arrange the test.
- An attic with almost no room to work in. If the hose can barely reach the eaves, it may make more sense to leave the attic and put the effort into the walls or the rim joists.
When the attic is already fine
If your attic is dry and already deep enough, we'll tell you to leave it alone. For what a top-up involves on price and where rebates come in, see attic insulation rebates and cost. Who qualifies comes down to the programme's current terms.
More on Blown-In Top-Ups
FAQ
Common questions about blown-in top-ups
Cellulose is heavier than loose fibreglass, settles more after it's blown and makes more dust on the day. It also clumps if a roof leak soaks it, and soaked cellulose has to come out. None of that rules it out. It's just why we check the ceiling and the roof deck before we choose it.
It depends on the product, so the figure to trust is the settled depth on that product's coverage chart. Cellulose and loose fibreglass hit the same R-value at different depths, and two fibreglass products can differ as well. Your installer should show you the chart on the bag and staple depth markers to the joists so you can check the result yourself.
Yes, blown-in insulation can go over old insulation as long as the old layer is dry and clean, with no mould or rodent damage. Anything wet or soiled comes out first, and if we find vermiculite, the work stops until a qualified lab has tested it. Before blowing, we fit baffles at the eaves and seal the air leaks at the ceiling, since both get buried once the top-up is in.
Yes, a bathroom fan duct that ends in the attic should be run outside before any insulation goes in. The fan blows warm, wet air right under the roof deck, and in winter that can turn to frost. Rerouting the duct is a job for the right trade, not us, so we point it out and book the top-up for after it's done.
Get a quote
Get an attic insulation quote in Mississauga
Call (437) 563-1473 or send the form. Tell us what you've noticed in the house, like a cold room, frost in the attic or a drafty floor. We'll look at the attic and give you a written list and a quote.