Spray Foam Contractors in Mississauga, ON
Closed-cell foam for rim joists, basement walls and garage ceilings. We'll also tell you straight where foam isn't needed at all.
As spray foam contractors in Mississauga, we spray foam basements, rim joists and garage ceilings: the tight, awkward spots where loose insulation can't stay put and can't stop air. Foam fills odd shapes and seals while it insulates. That's the reason to pay for it. An open attic floor is a different job, and blown-in usually does it better and for less.
Rim joists
The rim joist is the wooden band the floor framing sits on, right on top of the foundation wall. Go down to an unfinished basement and look up where the ceiling meets the wall. The ends of the floor joists butt into a board that runs around the whole house. That board is the rim joist.
It sits above ground, so the only things between it and January air are the sheathing and siding outside. A lot of the time it's bare, or someone has stuffed a loose fibreglass batt between the joists. Air gets in where the wood meets the concrete at the sill plate. You feel it as a cold draft along the basement floor, or in a main-floor room on an outside wall that never quite warms up.
Closed-cell spray foam suits this spot. It sticks to wood and concrete, wraps around wires and pipes, fills the odd pockets between joists, and seals the leak at the sill plate in the same pass that insulates the wood. A batt can't do that, because air just goes around it. In an older house with the basement ceiling still open, rim joist spray foam is often the first foam job we'd put on the list. The framing is easy to reach, and that's where the draft starts.
Basement walls
Foam goes on a basement wall only once the wall is dry. If water is getting through the foundation, at a crack, a tie hole or the joint where the floor meets the wall, a waterproofing contractor fixes that first. That isn't work we do. Spray foam over a wet wall just hides the problem until it turns up somewhere worse.
On a dry wall, basement spray foam insulation goes straight onto the poured concrete or block. Closed-cell foam insulates the wall and slows vapour moving through the foundation, so damp basement air can't get to cold concrete and condense behind a finished wall. Once the foam is bonded to the concrete, there's no gap left for that air to find.
The foam doesn't stay exposed. Building Science Corporation's digest BSD-114 says interior spray foam needs a drywall finish over it to protect it from fire, so foam on a basement wall gets covered. Your quote names who puts up that drywall before any work starts.
Rebates for foundation insulation fall under the Home Renovation Savings assessment path, and the programme's current terms decide what qualifies. Our page on rebates and cost covers what to check before you commit to a basement job.
The garage ceiling under a bedroom
A cold floor in the bedroom over the garage is a garage ceiling problem. The garage isn't heated, and if the floor framing between it and the room is short on insulation, the cold comes straight up through the subfloor. A rug and a space heater just paper over it.
Spray foam in the garage ceiling seals and insulates in one layer. It fills the joist bays around ducts and plumbing, which is exactly where batts get cut, squeezed and left full of holes. And it stays stuck to the underside of the subfloor instead of sagging away from it over the years.
Garage ceiling insulation only happens with the ceiling open. If yours is finished, it has to be opened first, and whoever puts the ceiling back has to restore it to fire-separation standard. We don't do drywall: we spray the open bays in between. The quote names who does that drywall. We never drill into a closed garage ceiling and pack foam in blind.
The ceiling and wall between a garage and the house form a fire separation. If we spot a gap or opening there, like a hole around a pipe or a missing piece of drywall, that's for a qualified contractor or the City to deal with. We'll point it out. We won't close it ourselves.
Closed-cell or open-cell
Closed-cell foam is dense and stiff once it sets, and it slows vapour. That's why we use it on rim joists, basement walls and garage ceilings, where a cold surface meets damp or outdoor air. Open-cell is softer and spongier and lets vapour through, so it needs a different plan for where the moisture ends up. Which foam goes where depends on the product's data sheet and the spot itself, not on habit, and your quote says which one is going on your house.
Where we'd leave the foam out
Foam earns its place in tight spots that need sealing and insulating at the same time. In plenty of other places it's the wrong call. As spray foam contractors in Mississauga, we'd rather tell you foam isn't the answer than sell it to you anyway. Here's how we sort it, spot by spot:
- An open attic floor: leave the foam out. Loose fill blown across the joists to the depth markers does the same job for less. If the question is attic insulation, the answer is usually a blown-in top-up.
- Dry attic insulation that's only a little thin: keep it. We top it up rather than tear it out for foam.
- A wet basement wall: no foam yet. The right trade fixes the water first, then we talk insulation.
- A wall that's already full: leave it. If the cavity is insulated and dry, foam on top adds cost and not much else.
- Vermiculite in the attic: this is where we put the tools down. Work stops, nobody disturbs it, and we recommend you have a qualified lab or abatement firm test it before anything goes ahead. We don't sample, test, vacuum or remove it ourselves, and we don't arrange the test.
Taking old spray foam out
Our crew takes spray foam out too, when there's a reason to. We cut and scrape it back from the framing or the concrete. Usually a leak behind it has to be found, a renovation is opening up the wall or ceiling, or the foam went on badly and has pulled away from the wood or left hollow pockets.
Whatever caused the problem gets fixed first, by the right trade, and then new insulation goes in. Our page on attic insulation removal walks through how a removal job goes and what comes out with it.
FAQ
Common questions about spray foam insulation
Homeowners remove spray foam when they need to get behind it: to find a leak, to make room for a renovation, or because it went on badly. Water trapped behind foam can't dry out and you can't see it, so the foam has to come off before anyone can find the source. Foam that has pulled away from the framing or left hollow pockets isn't sealing or insulating properly anymore. Our crew cuts and scrapes it back, and the cause gets fixed before anything new goes on.
The main drawbacks of spray foam are cost, permanence and the need to cover it. It costs more than blown-in for the same area, it's hard to get off once it sets, and indoors it needs a covering like drywall to protect it from fire. It can also hide a leak, which is why a wet wall gets fixed before any foam goes on.
Spray foam costs more than blown-in insulation for the same area, so we only use it where nothing cheaper will seal the spot. The price depends on the area, the thickness, closed-cell or open-cell, how easy the spot is to reach, what covering the foam needs afterwards and whether old insulation has to come out first. Your quote spells out each of those for your house.
Yes, spray foam on the inside of a basement wall has to be covered. Building Science Corporation's BSD-114 states that interior spray foam needs a drywall finish to protect it from fire. Your quote names who puts that drywall up.
Closed-cell foam is the one for a rim joist. It's dense, it slows vapour, and it seals the air leak at the sill plate while it insulates the wood. We check the product's data sheet to confirm it suits the spot before it goes on.
Get a quote
Get an attic insulation quote in Mississauga
Call (437) 563-1473 or send the form. Tell us what you've noticed in the house, like a cold room, frost in the attic or a drafty floor. We'll look at the attic and give you a written list and a quote.