We do wall insulation in Mississauga houses, and we insulate exterior walls without gutting them. Our crew drills small holes into each empty stud cavity, blows the insulation in tight as dense-pack, then plugs the holes. If your outside walls are cold and you would rather not open up a room to fix them, this is the job.

Is anything in your walls now?

You can often find out what is in your walls yourself with a screwdriver and a flashlight, before anyone quotes. It's a first look, though, not the final word.

  • Turn off the breaker for an outlet on an outside wall, take the cover plate off and shine the flashlight into the gap beside the electrical box. If you see fibreglass, loose cellulose or foam, the stud cavity has something in it. Bare sheathing or open air means it may be empty.
  • Look for a row of plugged holes, on the siding or on the inside walls, at about the same height in every stud bay. That usually means an earlier owner had the walls filled.
  • Ask the previous owners, or dig out old renovation paperwork if you kept it. One note about blown-in walls saves everyone a guess.
  • Notice which rooms feel cold. An outside wall that is cold to the hand in January hints that the cavity is empty or the fill has settled. It isn't proof, though. A draft at a window or along the rim joist can feel exactly the same.

Drill-and-fill, from outside or inside

Drill-and-fill is the standard way to blow insulation into walls that are already closed up. We drill small holes into each empty stud cavity, fill every bay until it is packed, then close each hole with a plug. What you actually get to choose is which side of the wall the holes go through.

That depends on your house and on what you would rather live with for a while: a row of plugged holes behind the siding, or patched spots on the inside walls waiting for paint. We tell you which side we would pick and why, and we look before we quote. The rest of what we do, attics to basements, is on the Prime Insulation home page.

From outside, through the siding

From outside, a strip of siding comes off first and the holes go through the sheathing behind it. Nothing changes inside, so your rooms stay as they are. The quote names who takes that strip off and who puts it back.

From inside, through drywall or plaster

From inside, the holes go through the drywall or plaster of the room. This suits a house where the cladding is hard to lift, or a room you were going to repaint anyway. We plug the holes. Any patching, sanding or paint beyond the plug is written on the quote, along with who does it.

How many holes go into each stud bay

Each stud bay gets at least one hole, sometimes more, depending on what sits inside it. A clear cavity can often be filled from a single hole. If a block of wood runs across the middle, or there is a window below, we drill another hole on the far side of it.

Why dense-pack has to be tight

Dense-pack has to be tight because loose fill settles in a wall and leaves a cold gap at the top of the stud cavity, right under the top plate. That empty band is where the cold wall comes back.

Our crew blows dense-pack cellulose through a narrow hose until the cavity is packed hard and the machine can't push any more in. Packed that firmly, the cellulose stays put. It also slows air moving through the wall, which loose fill barely touches.

Blocking, wiring and electrical boxes can stop the fill short. We probe each bay as we go, and if something is in the way, that bay gets an extra hole so the space past it fills too.

Brick-faced walls and sided walls

A brick-faced house can often still take drill-and-fill, because the brick may be a veneer over a framed wall with an empty stud cavity behind it. Then we fill from inside, through the drywall or plaster, and nobody touches the brick.

A sided house usually gives you both options. Vinyl or wood siding lifts off in strips, so we can work from outside, or we can come in through the rooms.

Solid masonry is another matter. If the wall is brick or block all the way through, there is no stud cavity to fill and drill-and-fill is off the table. We check which kind of wall you have, at an outlet, a window opening or in the basement, before we write a quote.

What wall insulation won't fix

Filling the walls slows heat and air through the wall itself. That's all it does. Some problems need something else first, and one needs nothing at all.

  • Water getting into the wall. Stains, soft drywall or peeling paint under a window mean water is coming in, and the right trade fixes that before any insulation goes in. Cellulose packed into a wet cavity just holds the water against the framing.
  • Old wiring we aren't sure about. If a cavity holds knob-and-tube or anything we can't identify, an electrician looks first and we wait for the answer.
  • Air leaks at the rim joist and in the attic. Filling walls does nothing for those spots. A draft along the basement ceiling or heat escaping through the top floor is a different job, such as a blown-in top-up over the attic floor once the ceiling leaks are dealt with.
  • Walls that are already full. If the cavities already hold insulation, more holes add nothing. We leave those walls alone.

Walls first or attic first?

The attic usually comes first, because an open attic floor is the simpler job and nothing has to be drilled or plugged to get at it. With the hatch open and the joists in view, our crew can see what is up there, keep it if it is dry and sound, and add what is missing.

Walls make sense once the attic is in good shape, or when one room stays cold along its outside walls no matter what the thermostat says. A corner bedroom with two outside walls may be where you notice it.

Either way, both jobs go on the written list in the order we would do them, and you decide how far to go. That list is how we tell you what is worth doing first.

Rebates for wall insulation sit in the Home Renovation Savings assessment path, and the programme's current terms decide what qualifies. Our page on insulation rebates and cost explains how that path works.

FAQ

Common questions about wall insulation

Existing walls take insulation through drill-and-fill. Our crew drills small holes into each stud cavity, blows in dense-pack cellulose until the bay is packed hard, and plugs the holes. The holes go either through the sheathing behind the siding or through drywall or plaster from inside. We check what is already in the walls first, since a full wall needs nothing.

No, the drilling doesn't weaken the wall, but it does leave plugged holes that need finishing. From inside, the plugs sit flush, and the spots need patching and paint before they disappear. From outside, the siding strip goes back over them. We plug every hole, and the quote names any finishing beyond that and who does it.

Yes, we can insulate walls without removing drywall, as long as the wall has an empty stud cavity to fill. We drill small holes through the drywall, or through the sheathing outside, fill each bay with dense-pack cellulose and plug the holes. The exception is a solid masonry wall with no cavity.

No, not when the stud cavity is already full. Drilling it adds nothing, so we leave it alone. If the wall holds loose fill that has settled and left an empty band at the top, we can fill that band through holes near the top plate. We confirm which you have before quoting.

Get a quote

Get an attic insulation quote in Mississauga

Call (437) 563-1473 or send the form. Tell us what you've noticed in the house, like a cold room, frost in the attic or a drafty floor. We'll look at the attic and give you a written list and a quote.

Call Text Quote